The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for work with with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it into the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need. For employ with 5/8” shaft sizes. Comes with set screws. Additional Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock steel Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets 
and equipment belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering on hand requirements and allowing for alterations in shaft size if important. The barrel of the split tapered bushing is normally split in two places and is keyed to the shaft. The barrel OD can be keyed to the travel component as well. The benefit of the split tapered bushing could it be will hold, regardless if the fasteners turn into loose. Split tapered bushings are interchangeable Split Taper Bushing china between manufacturers.
Taper bushing are widely used as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed of high quality engineered products with wonderful tolerance. The feature is easy to employ and needs no additional alteration. These bushings can match almost all sorts of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations add bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total range of both metric and imperial offered.
Standard range fits up to 125mm/5″ shafts & Hub diameter required is determined by the application.
Complete brief reach range readily available, for compact light-weight assemblies & Clean, Compact Style.
Ease of installation and removal.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.
Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that is built for durability and strength. U1 bushings are used in an extensively wide variety of applications, which include; sprockets, shaves, pulleys, gears, and much more, we as well offer most of these products. What units this bushing apart may be the high-quality steel construction along with exact manufacturing and high quality control; this means that you always get yourself a premium quality constant product. What really pieces us apart from the other guys is our highly trained expert staff members and our company-wide aim of customer satisfaction.
1. Be sure the tapered cone areas of the bushing and the within of the driven item happen to be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or additional component type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing remains loose to make sure sliding fit on shaft.
4. With key on shaft, slide the sprocket or other component type to the required placement on the shaft. Make sure to keep the heads of the cap screws attainable.
5. Align the sprocket or portion type, tighten the screws alternatively and progressively until they are pulled up tight. Do not use extensions on the wrench handles and do not permit the sprocket or part to become drawn i connection with flange of bushing. At this point there should be a gap between the bushing flange and sprocket, make sure this gap does not close.
Double split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or limited by mounting screws
External key of all sizes for confident drive and higher torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep up concentric bores
Available in in ., metric, and spline bores. Bore range from 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Travel – With keys upon both the shaft and product to provide the strongest possible travel.
3/4″ per Foot Taper on Barrel – Personal locking taper supplies the highest degree of mechanical locking merchandise to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for apply with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on the same page as the pulley you need. For employ with 5/8” shaft sizes. Includes set screws. Added Features: Manufactured from Steel For apply with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque capacity from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are utilized on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the necessity to have an element bored to size, preferably lowering on hand requirements and allowing for alterations in shaft size if important. The barrel of the split tapered bushing can be split in two areas and is keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The benefit of the split tapered bushing could it be will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.