The original sheave and pulley installation system developed to facilitate installation and alternative of components.
The QD (Quick Detachable) qd bushing china design provides for both conventional (flange outboard) and reverse (flange inboard) installation configurations.
1. Be sure the tapered cone areas of the bushing and the within of the driven item are clean and free from anti-seize lubricants.
2. Slide QD bushing on shaft, flange end first. Assemble key.
3. Placement QD bushing on shaft. Tighten set screw over key “hand tight” with regular Allen wrench only. Do not use excessive force.
4. Slide huge end of sheave or sprocket taper bore into placement over cone aligning drilled bolt holes in sheave or sprocket with tapped holes in flange of bushing. Assemble pull-up bolts and lock washers.
NOTE: Install M thru S bushings in the hub to ensure that the two extra holes in the hub can be found as far as feasible from the bushing’s saw cut.
5. Tighten pull-up bolts alternately and evenly to tightness indicated in torque table on back. Usually do not use extensions on wrench handles. There should be a gap between the face of the sheave or sprocket hub and the flange of the QD bushing to insure a reasonable cone grasp and press fit.
CAUTION: THIS GAP SHOULD NOT BE CLOSED.
Make use of a tapered or QD bushing from Ever-Power with sheaves, pulleys, sprockets and many other power tranny applications. Flanged quick-disconnect bushings include a completely split style to help provide easy set up and disassembly. A tapered bushing with directly edges uses an interior screw to greatly help drive the bushing into the shaft, while a split taper includes a flange and a key on the bushing to greatly help provide more drive.
QD bushings (in . and metric sizes) have a flanged style and show a 4° taper with standard or reverse installation. They are stocked in well-known finished bore sizes and minimum plain bore for customized reboring.
Many people refer to both types as a “taper lock” because they both utilize the tapered wedging action to lock to the shaft. The taper bushing, with it’s straight sides, runs on the set screw to drive the bushing into the bore of the component becoming set up (sheave, sprocket, etc.). Be careful when setting up these screws. The holes with threads on the bushing are for removal only. Also remember that the appearance of a flange externally of the bushing doesn’t indicate it’s a QD design. Split Taper bushing also has a flange, and both are not interchangeable. The QD style has a split that continues through the flange. The Steel QD (Quick Disconnect) Type bushing offers versatile and easy set up while providing exceptional holding power. QD Bushings are used thought out the industry offering convenience and design versatility. They are precision machined of quality Metal and are installed by tightening a number of cap screws. This draws the bushing into the taper bore of the product which compresses the bore of the bushing. QD bushings are often removed utilizing the cap screws as jack-screws. Double drilled holes are furnished in QD Bushings permitting mounting of product in the conventional or reverse positions. This enables cap screws to be installed through item hub or bushing flange whichever is certainly most convenient. A significant benefit in installation, cap screws are at all times inserted from the exterior where they are easily accessible. QD Bushings are available from stock with all well-known bores within the range of every size bushing.
QD Bushings include a split tapered flange with the split central to the flange and taper. They are used on sprockets, sheaves, and pulleys where more clamping force is necessary over standard bored-to-size bushings. Quick-Disconnect Bushings are essential for mounting v-belt drives, synchronous belt drives and roller chain drives.
Our direct supply chain to Martin Sprockets factories gets a wider selection of QD Bushings delivered at the right time at the right price.
Taper bushing are trusted together with sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered materials with great tolerance. The feature is usually easy to use and needs no additional alteration. These bushings can match almost all kinds of assemblies and sizes. They will be the best choice in design for mechanical connections.
No costly re-boring: complete range of both metric and imperial offered.
Standard range fits up to 125mm/5″ shafts & Hub diameter required depends on the application.
Complete short reach range available, for compact light-weight assemblies & Clean, Compact Design.
Simple installation and removal.
The initial sheave and pulley mounting system developed to facilitate installation and alternative of components.
The QD (Quick Detachable) design provides for both conventional (flange outboard) and reverse (flange inboard) installation configurations.
1. Be certain the tapered cone surfaces of the bushing and the inside of the driven product are clean and free from anti-seize lubricants.
2. Slide QD bushing on shaft, flange end 1st. Assemble key.
3. Placement QD bushing on shaft. Tighten set screw over key “hand tight” with regular Allen wrench only. Do not use excessive force.
4. Slide large end of sheave or sprocket taper bore into position over cone aligning drilled bolt holes in sheave or sprocket with tapped holes in flange of bushing. Assemble pull-up bolts and lock washers.
Notice: Install M thru S bushings in the hub so that the two extra holes in the hub are located as far as feasible from the bushing’s noticed cut.
5. Tighten pull-up bolts alternately and evenly to tightness indicated in torque desk on back. Do not make use of extensions on wrench handles. There must be a gap between your face of the sheave or sprocket hub and the flange of the QD bushing to insure a satisfactory cone hold and press fit.
CAUTION: THIS GAP SHOULD NOT BE CLOSED.
Make use of a tapered or QD bushing from Ever-Power with sheaves, pulleys, sprockets and many other power transmission applications. Flanged quick-disconnect bushings feature a completely split style to help provide easy installation and disassembly. A tapered bushing with directly edges uses an internal screw to help drive the bushing in to the shaft, 
while a split taper has a flange and an integral on the bushing to greatly help provide more drive.
QD bushings (in . and metric sizes) possess a flanged design and feature a 4° taper with standard or reverse mounting. They are stocked in popular finished bore sizes and minimal plain bore for customized reboring.
Many people make reference to both types as a “taper lock” because they both utilize the tapered wedging action to lock to the shaft. The taper bushing, with it’s straight sides, uses a set screw to drive the bushing into the bore of the component getting set up (sheave, sprocket, etc.). Be cautious when setting up these screws. The holes with threads on the bushing are for removal only. Also remember that the looks of a flange on the outside of the bushing doesn’t necessarily mean it’s a QD design. Split Taper bushing also has a flange, and the two aren’t interchangeable. The QD style has a split that proceeds through the flange. The Steel QD (Quick Disconnect) Type bushing offers versatile and easy installation while providing exceptional holding power. QD Bushings are utilized thought out the industry offering comfort and design versatility. They are precision machined of quality Metal and are set up by tightening several cap screws. This draws the bushing in to the taper bore of the product which compresses the bore of the bushing. QD bushings are easily removed utilizing the cap screws as jack-screws. Double drilled holes are furnished in QD Bushings permitting installation of product in the traditional or reverse positions. This enables cap screws to be installed through item hub or bushing flange whichever is definitely most convenient. A significant benefit in installation, cap screws are generally inserted from the outside where they are easily accessible. QD Bushings are available from stock with all well-known bores within the number of every size bushing.
QD Bushings include a split tapered flange with the split central to the flange and taper. They are used on sprockets, sheaves, and pulleys where more clamping push is necessary over standard bored-to-size bushings. Quick-Disconnect Bushings are crucial for mounting v-belt drives, synchronous belt drives and roller chain drives.